| Socket Adapter (click to buy) | Description | Package | Devices Supported | Adapter Capacity per Site | Sockets per Adapter | Adapter Price | Replacement Socket Card | 2900L, 3910, 4910, 3928, 3901, 3900, 2900, 4900, 1900 | 3710-MK2, 4710 | 3610, 4610 | 1710, 2710M, 2710 | 2610, 1610 |
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| ASMR48TQZ | Automated SOCKET MODULE, 48 PIN QFP | LQFP(48) | 55 | 1 | 1 | $862.53 | LX4ASMR48TQZ | ✔ | ✔ | ✔ | ✔ | |
| FX4ASMR48TQZ | Automated SOCKET MODULE, 48 PIN QFP | LQFP(48) | 46 | 1 | 4 | $2,090.85 | LX4ASMR48TQZ | ✔ | ✔ | |||
| FX4SMR48TQZ | SOCKET MODULE, 48 PIN QFP | LQFP(48) | 46 | 1 | 4 | $2,013.38 | LX4ASMR48TQZ | ✔ | ||||
| LX4ASMR48TQZ | Automated REPLACEMENT D-CARD | LQFP(48) | 64 | 2, 3 or 4 | 1 | $345.00 | ✔ | |||||
| SMR48TQZ | SOCKET MODULE, 48 PIN QFP | LQFP(48) | 55 | 1 | 1 | $631.67 | LX4ASMR48TQZ | ✔ | ✔ |
| Device Name | Freescale Semiconductor MC9S08DZ60MLF |
| Manufacturer | Freescale Semiconductor |
| Part Number | MC9S08DZ60MLF |
| 8-bit Bytes | 65536.0 |
| Vcc(program) | 4.5 |
| Set programming | nan |
| Memory Regions | 1080h-13FFh; 1400h-17FFh; 1900h-FFA7h; FFA8h-FFBFh; FFC0h-FFFFh; |
| Electrical Erase | Yes |
| Packages | LQFP(48) |
| Notes | IMPORTANT: ********This algorithm supports only half of the EEPROM in the memory map[$1400-$17FF].*******************The EEPROM is configured in 8-byte sector mode (EPGMOD=1)during Program/Read/Verify.*********** The following describes the Buffer setup: Addresses [$1080-$13FF] are FLASH. Addresses [$1400-$17FF] are EEPROM. Addresses [$1900-$FFFF] are FLASH. There are some location reserved in the FLASH memory map. The following are reserved addresses:[$FFAE-FFAF] [$FFB8-$FFBC] and $FFBE. These locations will be ignored during Programand Verify. Erase command will be erase entire FLASH memory map included reserved memory. The lower two bits (Bit1 and Bit0) at address $FFBF are security bits (SEC01:SEC00). They are ignored during Program and Verify and read 1:0 if unsecured during Read and Compare. To secure the device use SECURE command. The EPGMOD(bit 5) at address $FFBF is EEPROM mapping mode option. This bit is ignored during program and Verify. EPGMOD bit can be programmed under Secure option. *** During Erase factory programmed trim value at addresses [$FFAE-$FFAF] will be saved first and restored at the end. Erase will fail if the device is secured. If the device fails erase the Factory Trim value might be corrupted. The part cannot be used unless re-trimmed. |
| Programmer | 3900 |
| Socket Modules | LX4ASMR48TQZ |
| Device Name with Package | Freescale Semiconductor MC9S08DZ60MLF LQFP(48) |
| Device Name with Package and Adapter | Freescale Semiconductor MC9S08DZ60MLF LQFP(48) LX4ASMR48TQZ |